High quality machined brass shaft collars that are great for wire landing gear and axle shafts. Enough stock so that threads will not strip and can be reworked for many other uses. Includes set screw and one wrench. (Wrench not included with #243 & 244) Allen Wrench Sizes:
Ready to use Starters (formally known as 2301 Igniters) for your model rockets. Requires one per launch to ignite your engine. Six to a pack for your convenience.
Dependable, easy-to-use Estes Starters. Works just like our 2301 Igniters.
Estes model rocketry is recommended for ages 10 and up with adult supervision for those under 12. Unless otherwise specified, all models require assembly. Tools, construction and finishing supplies sold separately. In order to launch, a launch system, model rocket engines, starters and recovery wadding are required – sold separately-unless otherwise specified.
Du-Bro fuel tanks were designed with toughness in mind! Our fuel tanks will not split or crack from vibration or pressure. In fact, our fuel tanks can be used with pressurized fuel systems! Du-Bro fuel tanks come complete with all of the hardware including our one piece clunk with fuel barbs built right on the clunk stem, your fuel tubing will not slide off! Du-Bro fuel tanks can be used with either glofuel or gasoline if you purchase our Cat. No. 400 Gasoline Conversion Stopper. Next time you build a model, choose a Du-Bro fuel tank.
Pack of 2 dispensing syringes and 3 sizes of stainless steel needles for accurate application of water based glues:R/C Modellers Glue(AD12), Speedbond(AD10),Aliphatic Resin(AD8), Tacky Glue(AD27), Decorator Glue(AD26).Easy to clean syringes and tips using warm soapy water.
Stop tips clogging by resting tips on damp sponge or in water.
This is a pack of two Du-Bro 1/4 Scale Turnbuckles. Dubro 1/4 Scale Turnbuckles are not only completely functional, they look awesome too! When attached to your guy wires (flying wires) they add a touch of functional class to all larger scale models.
1/16 in (1.5mm) axle diameter. Tailwheel Brackets are made of lightweight durable nylon. Available in three sizes to fit most airplanes from .40 size to large scale. Includes 1 bracket, 1 wire form, 1 dura-collar and 3 flat washers.
Wheel not included; review Du-Bro's large selection of tailwheel choices.
ProTek RC 3x12mm "High Strength" Socket Head Cap Screws (10)
This is a pack of ten 3x12mm "High Strength" Socket Head Cap Screws from ProTek R/C. These are made from metric grade 12.9 steel which has a minimum tensile strength of 174,000 PSI. These screws are the strongest you can get and are suitable for the most demanding applications! Most manufacturer brand screws are not grade 12.9 steel, so these are a great upgrade for your car, truck or helicopter!
Top Flite brand MonoKote's superior shrink and adhesion make it an extremely easy plastic covering to apply. And once applied, its special adhesive gets a grip that not even years of accumulated exhaust residue can break. MonoKote is also one of the most puncture and scratch-resistant films on the market - qualities you'll find in all of the rich, vibrant colors available.
MonoKote is a thin, clear, protective film with a pigmented, heat-activated adhesive on the back specially formulated for model airplanes. MonoKote is applied with a sealing iron. Heat from the iron shrinks the film while simultaneously activating the adhesive tightly bonding it to your model. When MonoKote is not heated, the adhesive is not sticky. The adhesive side has a clear, protective backing that must be removed before application.
Can be applied quickly and easily using a heat gun or sealing iron for professional-quality results.
Extra pliable — conforms readily to compound curves for a wrinkle-free finish.
Puncture-resistant and easy to repair. Small "dents" disappear just by reheating!
Allows easy cleanup of smudges or exhaust residue using detergent and water or Top Flite MonoKote Cleaner Polish
Attaching to Wood:215-240° F (102-116° C)
Partial Shrinkage:230-270° F (110-132° C)
Maximum Shrinkage:270-350° F (132-177° C)
Note:MonoKote is best-suited for medium-size models in the 2 lb. (1000g) range and up. Smaller/lighter models may be more suitable for MonoKote's lighter, low-heat/low-shrink cousin EconoKote (though EconoKote may be used on larger models, too).
Monitor (not included) can be added or removed with a single strap
The SPMVM430HA headset provides users with an affordable 5.8GHz FPV headset when paired with the SPMVM430 monitor. Owners of the VM430 monitor can simply snap the monitor into the headset for an incredible FPV experience. The headset includes an adjustable head-strap for optimal comfort and weights only 380g with monitor.
Key Features easy to install 2 per package Overview Nylon and Carbon filled Gold-N-Rods feature an exclusive spline design that reduces friction and eliminates sensitivity to dirt, dust and moisture. They are very easy to install -- a threaded stud screws into the inner rod, and a clevis attaches to the other end of the stud -- and they are versatile, as they are unaffected by fuel. They can be used for any part of the control system, and are made in sizes and lengths to fit just about any application.
Clevises, studs and other hardware are included in all kits. To assemble, simply cut the pieces to length and glue or clamp (see hardware) the outer sheath in place. The threaded studs simply self-thread into the inner rod (easily done with a cordless drill) and the clevises thread onto the studs.
12 oz tank measurements: 2 1/4 H x 2 9/16 W x 5 3/8 Long. Du-Bro Fuel Tanks are designed to be tough! Our fuel tanks will not split or crack from vibration or pressure. In fact, our fuel tanks can be used with pressurized fuel systems! Comes complete with all hardware, including our one piece clunk with fuel barbs built right on the clunk stem. Your fuel tubing will not slide off! Du-Bro Fuel Tanks can be used with either glow fuel or gasoline if you purchase our catalog #DUB400 Gasoline Conversion Stopper.
This tool makes installation or removal of 2-56 and 4-40 clevises and retaining clips a breeze. Crafted from heat-treated steel, it features a notch on each end for holding 2-56 and 4-40 clevises open and a slot for removing retaining clips. The tool is magnetized to prevent retaining clip loss.