IN Store Pickup Available
Select In Store Pick up at Checkout
Team Associated RC8T3 Front Arms
Team Associated RC8T3 Front Arms. These are the stock replacement front lower arms for the RC8T3 and RC8T3e trucks.
Team Losi Racing 6.5" Precut Medium Downforce Wing (2) *Discontinued
This is a pack of two Team Losi Racing 6.5" Precut Medium Downforce Wings. The 6.5” wide TLR Medium Downforce Rear Wing provides fantastic grip and stability in all conditions. It’s made from 1.2mm thick lexan for longer life and has raised end plates for extra tire clearance. Three scribe lines across the rear offer repeatable wickerbill trimming options.
Team Associated Differential Spur Gear (81T) *Sale
This is a replacement Team Associated B44.3 81 Tooth Differential Spur Gear.
Team Losi Racing Carbon Rear Shock Tower **DISCONTINUED
This is a replacement Team Losi Racing Carbon Rear Shock Tower, and is intended for use with the Team Losi Racing TEN-SCTE 2.0 1/10 scale 4WD short course truck.
Team Losi Racing 22-4 Cab Forward Body Set (Clear) (Sale)
This is a Team Losi Racing 22-4 Cab Forward Body Set.
Spektrum RC 17g Analog Servo *Discontinued
This is a replacement E-flite 17g Analog Servo, with a 400mm wire lead. This servo is intended for use with the Pulse 15e Airplane.
Mugen Seiki 13T Clutch Bell **DISCONTINUED
This is a replacement Mugen 13 Tooth Clutch Bell, and is intended for use with the Mugen MBX6 family of 1/8 scale vehicles. This is a stock replacement.
Team Losi Racing Ballstud & Hub Spacer Set (TLR 22) **DISCONTINUED
This is a Team Losi Racing Ballstud & Hub Spacer Set, intended for use with the Team Losi Racing 22 1/10 buggy.
Team Losi Racing Aluminum/Brass Mid Motor Rear Camber Block **DISCONTINUED
This is an optional Team Losi Racing Aluminum/Brass Mid Motor Rear Camber Block. The TLR Race Team has done extensive testing this year tuning their Mid-Motor 22 2.0’s and 22SCT 2.0’s with brass weight from front to rear. For medium to low grip tracks, adding 14g of additional weight over the rear of the vehicle improvement balance on the 22 2.0 and 22SCT 2.0. It gets 14g of extra ballast as low and as far to the rear of the vehicles as possible. This has helped to increase the rear weight bias of the 22 2.0 and 22SCT 2.0, which creates more rotation and forward drive, and an all-around better balance.
Run as a standard part on the team’s MM 22’s for quite a while, the Aluminum Rear Camber Block is unchanged, adding durability to the rear camber link’s inner ball stud – we’ve just now added the brass base for greater fine tuning. Machined from high quality brass and 7075-T6 aluminum, the MM Camber Tower will fit the 22, 22 2.0, 22T, 22SCT, and 22SCT 2.0 without any further parts of modifications in Mid-Motor configuration, but will NOT fit any of the 22 vehicles in Rear-Motor configuration.
Traxxas TRX 3.3 Engine, Multi Shaft, Pull Start * Discontinued
This is the Traxxas TRX 3.3 Multi Shaft Racing Engine with Pull Starter. This version includes threaded crankshaft inserts for short and standard applications.
Other versions of the TRX 3.3 engine include; #5404 Single Shaft without Starter, TRAG5404 #5406 Multi-Shaft without Starter, #5407 Single Shaft w/Recoil Pull Starter, TRAG5407 Some notes on slide valve and rotary carburetors. Rotary carbs offer a larger response in the middle of the power band. This works well for off-road applications when throttle response must be varied. Slide Valve carbs provide greater response at the beginning and end of the power band. This works well for on-road and racing applications for fast take-offs and high speed.
Losi Aluminum Rear Hinge Pin Braces (2) *Discontinued
This is a replacement Losi Aluminum Rear Hinge Pin Brace Set for the Monster Truck XL.
Team Losi Racing SCTE Aluminum Rear Hex Set (+0.5mm Width)
This is an optional Team Losi Racing TEN-SCTE +0.5mm Aluminum Rear Hex Set. Each hex increases the rear width 0.5mm. Package includes two hexes, two screws and two pins.
Effects of Rear Track Width Adjustment:
Spektrum RC 500WP Digital Servo
This is a Spektrum 500WP Digital Servo. This servo is compatible with the Losi Mini 8IGHT and Mini 8IGHT-T vehicles with AVC, but is faster and stronger than the servo included with non AVC equipped Mini 8IGHT vehicles making it a great option for those vehicles as well.
Size Category: Minis and Micros
Torque: 54 oz-in @ 6.0V
Speed: .16 sec/60 degrees @ 6.0V
Bushing Or Bearing: Bushing
Gear Type: Nylon